pv7 pecl vcxo series 6 pad leadless surface mount pecl voltage controlled xtal os cillator differential pecl output with enable/disable standard specifications part numbering guide consult factory for available frequencies and specs. not all options available for all frequencies. a special part numbe r may be assigned. frequency stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration a nd load (425) 776 - 1880, fax: (425) 776 - 2760, ple - sales@pletronics.com, www.pletronics.com 19 pl tronics, inc. packaging tube or 24mm tape 16mm pitch portions of the part number that appear after the frequency may not be marked on part (c of c provided) apr 2004 overall frequency stability operating temperature range 0 to +80 c is standard, but can be extended to storage temperature range - 55 to +125 c - 40 to +85 c supply voltage (vcc) 3.3 volts 5 % available. see test cirucit 5. e/d internal pullup 50 kohm minimum to vcc output symmetry 40/60% referenced to 50% of amplitude output rise & fall (tr & tf) 1.0 ns maximum when vth is 10% and 90% of waveform 100 ma maximum supply current (icc) 2.275 v minimum referenced to ground, vcc = 3.300v, 0.975 v minimum referenced to termination voltage, - 1.025 v minimum referenced to vcc output high level 1.680 v maximum referenced to ground, vcc = 3.300v, 0.380 v maximum referenced to termination voltage, - 1.620 v maximum referenced to vcc output low level 5 ps rms maximum measured from 12 khz to 20 mhz from output frequency jitter v enable 0.7 vcc minumum referenced to ground 0.3 vcc maximum referenced to ground v disable 50 ppm linerarity slope positive and montonic control voltage range (cvr) 0.0 to 3.3 v pullability pull range is defined as absolute pull range. this is the pu ll range about the specified oscillator frequency, independent of supply, temperature range and load. 10% typical over operating temperature range output enable / disable (e/d) output enable time 200 ns maximum at output enable or 1 ms maximum at output en abled and stable high level input current low level input current -20 ua maximum at enable / disable pin = 0.7 vcc -200 ua maximum at enable / disable pin = 0 v 200 ns maximum at output disable output disable time vcc supply current disabled < 1 ma. both outputs are high im pedance when disabled. frequency stability frequency in mhz frequency deviation (pullability) absolute pull range pv7 5 v b v - 100.0m - xxx (internal code or blank) v: 50 ppm operating temperature range b: 0 to +70 c f: - 40 to +85 c 5 = 50 ppm model supply voltage v = 3.3 volts 5 % w = 2.5 volts 5% 70.00 mhz ? 200.00 mhz consult factory for higher frequencies pl tronics , inc. 19013 36th ave. w, suite h lynnwood, wa 98036 usa manufacturer of high quality frequency control products .
pv7 pecl vcxo series (425) 776 - 1880, fax: (425) 776 - 2760, ple - sales@pletronics.com, www.pletronics.com 19a pl tronics, inc. pl tronics , inc. 19013 36th ave. w, suite h lynnwood, wa 98036 usa manufacturer of high quality frequency control products . mar 2004 0.055 (1.4) 0.024 (0.60) 0.050 (1.27) 0.004 (0.10) 0.200 (5.08) 1 3 4 6 0 .055 (1.4) 0.200 (5.08) 5 2 0.075 (1.9) 0.276 (7.0 .15) 0.197 (5.0 .15) max 2 5 1 6 0 .079 (2.0) 0 .087 (2.2) 4 3 mechanical: not to scale inches (mm) solder pads due to part size and factory abilities, part marking may var y from lot to lot and may contain our part number or an inte rnal code. 1 vcon 2 e/d 3 vss 4 out 5 c out 6 vcc pin signal see page 6 for layout guidelines
|
